Hvordan blinker brugerdefineret eller lager ROM med Odin-tilstand, der fungerer? (fra en dårlig blinket Galaxy A20, se billede)

Blinker den rigtige img løste problemet:

heimdall flash --RECOVERY TWRP-3.3.1.0_A20_V1.2_by_Agrim720\[Black-themed\].img.img 

Fil blev fundet her: XDA-forum

Enhed: A205GUBU4ASK2

Tidligere rodfæstet med boot.img patched af magisk og vbmeta blinkede:

heimdall flash --BOOT magisk_patched.img heimdall flash --VBMETA vbmeta.img 

Jeg kan varmt anbefale at undgå Samsung-enheder. Motorola-enheder, f.eks. er bedre til tilpassede ROMer.

Hvis enheden klager over “officielle binære filer”, er der behov for omgå KG-tilstand .

Kommentarer

• TWRP fungerede dog kun første gang. Efter at jeg havde formateret Data og genstartet, startede enheden med puritanisme omkring " officielle binære filer ".
• Jeg havde brug for omgå KG-tilstand. svar opdateret. tak.

For Heimdal:

Jeg henviser til Udviklere læser mig fil til linux-kommandolinjeanvisninger:

Blinkende firmware fra kommandolinje:

1. Fully charge your phone (use the wall charger as it"s faster). 2. Download a decrypted device ROM or a Heimdall Firmware Package and extract everything to the one directory. 3. If the ROM is not a Heimdall Firmware Package it may instead be provided as multiple archives (nested or otherwise), extract them all to the same location. NOTE: If you want to use the CSC then extract it last. 4. Put your Galaxy S device into download mode and plug it in.. 5. Open a terminal and navigate to the directory where you extracted the ROM/firmware files. 6. Type the following to list all the functionality Heimdall supports: heimdall help 7. Before flashing, you must first know the names of the partitions you wish to flash. These can be obtained by executing: heimdall print-pit --no-reboot The inclusion of --no-reboot ensures the phone will not reboot after PIT file has been downloaded and displayed. After executing a command with the --no-reboot argument, the next command should include the --resume argument. NOTE: You can still safely reboot your phone manually (with the power button) after executing --no-reboot commands. 8. Use the help and print-pit output to construct a command with all the files you want to flash. Here is an example that does a full flash and repartition on a GT-I9000: heimdall flash --repartition --resume --pit s1_odin_20100512.pit --FACTORYFS factoryfs.rfs --CACHE cache.rfs --DBDATA dbdata.rfs --IBL+PBL boot.bin --SBL Sbl.bin --PARAM param.lfs --KERNEL zImage --MODEM modem.bin 9. Heimdall will display the progress as it flashes so that you know things are working as they should. 

Sådan oprettes en Heimdall Firmware-pakke:

Firstly, Heimdall"s firmware package format is just a regular TAR archive compressed with gzip. The only two real requirements are that a valid firmware.xml must be included (refer to Appendix A) and you can only include files (no directories, links etc.) As such if you"d like there is nothing preventing you from creating Heimdall packages manually. Of course Heimdall Frontend provides a simple user interface that takes care of all the hard work for you. There are two ways in which you can create a firmware package. You can create a package from scratch, or you can load an existing package, apply modifications and then save the package. Creating a package from scratch is the preferred approach, by taking this approach you"re far less likely to run into file name length limitations. Before you can access Heimdall Frontend"s firmware creation functionality (available from the "Create Package" tab) you must first specify which files will be included in your package, as well as a few flashing options i.e. Whether or not users should repartition when flashing. This information must be filled out from the "Flash" tab in exactly the same fashion you would provide information to flash your device (see "Performing a Custom Flash with Heimdall Frontend"). As mentioned above, it"s not the preferred means, but you"re able to load an existing package as a starting point for this information. Once you"ve specified the files/partitions you wish to include in your firmware package the "Create Package" tab will become available. Clicking this tab will display additional information that you can include in your package. In order to continue you must fill out all sections except for the URLs section, which is optional. The following is a break-down of what all these options mean. 

For Odin:

Afhængigt af hvilken Odin-version du bruger det kan være lidt anderledes. En nyere Odin-version er ret enkel:

Sørg for, at din bootloader er opdateret med enhedens firmware eller opdateret. Kontroller u# inden for firmwarens zip / tar-navn.

1) pakke .zip af den officielle firmware ud.

2) Start Odin.

3) tilslut din enhed via USB. Når en enhed er tilsluttet, skal den vises i com-feltet.

4) vælg AP, gå inden for markeringen til din udpakkede firmware og vælg tar.md-filen eller tar-filen.

Sørg for, at du ikke vælger / aktiverer noget med pit-indstillingen.

5) Når indlæst skub start-knappen, og lad det være så det er noget.

Det skal tage lidt eller gå op til tyve minutter eller mere at starte. Når du er startet, skal du være god at gå med firmwaren.

Hvis du har mere end bare en enkelt tar- eller tar.md5-fil, skal du:

1) pakke .zip af den officielle firmware ud.

2) zipen kan omfatte en række ting (filer) såsom AP, BL, CP, CSC.

3) start Odin.

4) tilslut din enhed via USB. Når den er tilsluttet, skal en enhed vise op i com-feltet.

5) vælg hver af de forskellige felter, og inden for markeringen anbring de tilknyttede filer i det rigtige felt. AP (system), BL (Bootloader), CP (modem), CSC (Device Varia nt).

Sørg for, at du ikke vælger / aktiverer noget med indstillingen pit.

6) Når den er indlæst, skal du trykke på startknappen og lade den være sådan.

Kommentarer

• link til heimdall supporttråd forum.xda-developers.com/showthread.php?t=755265